CCNA Final Internal Exam 200-301 (Part-1-3)

Which command is used to display the collection of OSPF link states?

Refer to exhibit.What Administrative distance has route to 192.168.10.1?

What causes a port to be placed in the err-disabled state?

Which output displays a JSON data representation?

Which command on a port enters the forwarding state immediately when a PC is connected to it?

Which configuration is needed to generate an RSA key for SSH on a router?

A packet is destined for 10.10.1.22. Which static route does the router choose to forward the packet?

With REST API, which standard HTTP header tells a server which media type is expected by the client?

Which unified access point mode continues to serve wireless clients after losing connectivity to the Cisco Wireless LAN Controller?

Refer to the exhibit. If configuring a static default route on the router with the ip route 0.0.0.0 0.0.0.0 10.13.0.1 120 command, how does the router respond?

Which command verifies whether any IPv6 ACLs are configured on a router?

Refer to the exhibit. What is the effect of this configuration?

Which command must be entered when a device is configured as an NTP server?

Refer to the exhibit. Which address and mask combination represents a summary of the routes learned by EIGRP?

Refer to the exhibit. If the network environment is operating normally, which type of device must be connected to interface FastEthernet 0/1?

Refer to the exhibit. Which type of route does R1 use to reach host 10.10.13.10/32?

Which command is used to specify the delay time in seconds for LLDP to initialize on any interface?

Refer to the exhibit. When PC 1 sends a packet to PC2, the packet has. Which source and destination IP address when it arrives at interface Gi0/0 on router R2?

Refer to the exhibit. An administrator must turn off the Cisco Discovery Protocol on the port configured with address last usable address in the 10.0.0.0/30 subnet. Which command set meets the requirement?

Refer to the exhibit. Which route type is configured to reach the internet?

What does an SDN controller use as a communication protocol to relay forwarding changes to a southbound API?

Refer to the exhibit. If OSPF is running on this network, how does Router 2 handle traffic from Site B to 10.10.13.128/25 at Site A?

Refer to the exhibit. When running EIGRP, what is required for RouterA to exchange routing updates with RouterC?

Which component of an Ethernet frame is used to notify a host that traffic is coming?

Router R1 must send all traffic without a matching routing-table entry to 192.168.1.1. Which configuration accomplishes this task?

Refer to Exhibit. How does SW2 interact with other switches in this VTP domain?

Which API is used in controller-based architectures to interact with edge devices?

In Which way does a spine-and-leaf architecture allow for scalability in a network when additional access ports are required?

Which command is used to configure an IPv6 static default route?

How does STP prevent forwarding loops at OSI Layer 2?

Which mode allows access points to be managed by Cisco Wireless LAN Controllers?

Which configuration ensures that the switch is always the root for VLAN 750?

Refer to the exhibit. Which switch in this configuration will be elected as the root bridge?

Refer to the exhibit. Which route type does the routing protocol Code D represent in the output?

Refer to the exhibit. After you apply the given configuration to a router, the DHCP clients behind the device connot communicate with hosts outside of their subnet. Which action is most likely to correct the problem?

Which implementation provides the strongest encryption combination for the wireless environment?

Refer to Exhibit. Which action do the switches take on the trunk link?

Refer to the exhibit. Which command configures a floating static route to provide a backup to the primary link?

Which technology can prevent client devices from arbitrarily connecting to the network without state remediation?

Refer to the exhibit. Based on the LACP neighbor status, in which mode is the SW1 port channel configured?

Refer to the exhibit. Which prefix does Router 1 use for traffic to Host A?

Which 802.11 frame type is association response?

Refer to the exhibit. Which type of configuration is represented in the output?

Which command prevents passwords from being stored in the configuration as plaintext on a router or switch?

Which protocol does an access point use to draw power from a connected switch?

Refer to the exhibit. Router R1 is configured with static NAT. Addressing on the router and the web server are correctly configured, but there is no connectivity between the web server and users on the Internet. What is a possible reason for this lack of connectivity?

What is the benefit of using a Cisco Wireless LAN Controller?

An engineer needs to configure LLDP to send the port description time length value (TLV). What command sequence must be implemented?

A network administrator needs to aggregate 4 ports into a single logical link which must negotiate layer 2 connectivity to ports on another switch. What must be configured when using active mode on both sides of the connection?

Refer to the exhibit. An engineer configured NAT translations and has verified that the configuration is correct. Which IP address is the source IP?